Liefern und montieren von: 10/100Base-TX (RJ-45) [100 m/328 ft.] to 100Base-X SFP Slot (empty) **Lantronix / Transition Networks **Direct Attach Cables / Active Optical Cables A simple to install, cost-effective and interoperable solution Often used for data center short-reach interconnects, Direct Attach, Active Copper and Active Optical Cables are an indispensable part of any network. Terminated with transceiver-style connectors, they are designed to be used in the same ports as a typical SFP+ or QSFP transceiver, with no need for adapters or converters. Our DAC and AOC cables offer compatibility with a huge range of vendors, enabling the connectivity you need within the Top of Rack and End of Row environments. • 10G, 25G, 40G & 100G product solutions • Seamless interoperability with network equipment • Multi-code options enabling different OEM vendors at each end of the cable • 4x breakout cables, 40G QSFP+ to 4x 10G SFP and 100G QSFP28 to 4x 25G SFP28 • Fast Delivery, Custom solutions • Compatible with Over 90 Systems • Savings of up to 70% **Converters and Device Servers The ION C2210 is a media converter module that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber. The ION C2210 is a manageable device when installed in a managed ION chassis. **Features • Auto-Negotiation of speed and duplex on TP port • Auto-MDI/MDIX on TP port • Link Pass Through (LPT) • Far-End-Fault (FEF) detection • Pause (Software Controlled) • Automatic Link Restoration • Field Upgradeable Firmware • Can be used in any ION Platform Chassis • Standards based, will link with any Standard 10/100Base-TX and any Standard 100Base-FX ports **Manageable Features • Report converter status to chassis management software: • TP and Fiber Link Status • Hardware switch settings • Copper Port Speed • TP and Fiber Port Duplex • Fault condition • Write operation includes: • Power on/off device • Auto-Negotiation enable/disable • Force 10 Mbps or 100 Mbps • Force half or full-duplex • Select advertising modes when • Auto-Negotiation is enabled • LPT enable/disable • FEF enable/disable • Pause enable/disable • Auto-MDI/MDIX enable/disable Note: Manageable Features are available when used in an ION Platform chassis along with an ION Management Module. **TECHNISCHE_DATEN ***Standards • IEEE 802.3u • IEEE 802.3x ***Data Rate • 10 Mbps; 100 Mbps Layer 2 ***MAC Address Table • 1K ***Frame Buffer Memory • 512 Kbits ***Max Frame Size • 2048 bytes ***Switch • SW1: Auto-Negotiation (UP = enabled) • SW2: Forced 100 Mbps/10 Mbps with Auto-Neg. off (UP = 100 Mbps) • SW3: Forced Full/Half-Duplex with Auto-Neg. off (UP = Full) • SW4: Full/Half-Duplex on fiber port (UP = Full) • SW5: Auto-MDI/MDIX on UTP (UP = enabled) • SW6: Link Pass Through (UP = enabled) ***Internal Jumper • Auto-MDI/MDIX: Enable/Disable ***Jumper • Hardware: Mode of operation is determined by the settings on the 4-position switch • Software: Mode of operation is determined by the most recently saved on-board microprocessor settings ***Status LEDs • FD (Fiber Duplex): ON= Full-duplex on fiber • LACT (Fiber Link/Activity): ON = Fiber Link • PWR (Power): ON=Connection to powered backplane • (TP. Duplex/Link): Yellow = Half duplex, Green = Full-Duplex • (TP. Speed): Yellow = 10Mbps, Green = 100 Mbps ***Dimensions • Width: 0.86” [22 mm] • Depth: 6.5” [165 mm] • Height: 3.4”[86 mm] ***Power Consumption • 2.5 Watts, 200 mA @ 13.9 VDC ***Environment • Environment specs are dependent on the chassis chosen • Operating: 0°C to 50°C • Humidity: 5% to 95% (non-condensing) • Altitude: 0 – 10,000 ft. ***Weight • 1 lb. [0.45 kg] ***MTBF • Greater than 250,000 hours (MIL-HDBK-217F) • Greater than 667,500 hours (Bellcore) ***Certifications • CISPR/EN55022 Class A, FCC Class A, CE Mark, EN55024 ***Warranty • Lifetime QS-Managementsystem nach ISO 9001/2008, ISO 14001 und TL 9000 Art.-Nr.: C2210-1040 Hersteller: tde - trans data elektronik GmbH Stück_____________ Einzelpreis__________ Gesamtpreis__________